Shutdown Button not working on Pi5 and NuclearFission

[SentinelFour]

Hi,

as per the title , the shutdown button is not working. It's a NuclearFission with a Pi5.

• I installed everything via RHIM -> button was not working.
• I installed everything using the NuclearQuads install script -> button does work.
• Then I installed everything once again via RHIM -> buton not working.

And for the port forwarding issue which I encountered as well, I see that a different issue was already opened. :)

Thank you!

[szafranski]

thanks for reporting, will investigate soon

[szafranski]

port forwarding fixed. will investigate the button issue

[SentinelFour]

Thanks a lot! Awesome. :)
Thought about following up here today but thought you will look at it whenever you find the time. Intended to test the latest beta today and RHIM is just the most convenient way to update.

I would assume that the config file is not populated correctly for the raspi5. That it is not related to the NH fission.
I'm no expert but if I am not mistaken something was missing in the config when I compared it to the one that exists after the NH script installation.

[szafranski]

Newest beta is supported. What is the issue on pi5?

…

On Fri, Apr 25, 2025 at 20:20 SentinelFour ***@***.***> wrote: *SentinelFour* left a comment (RotorHazard/RH_Install-Manager#28) <#28 (comment)> Thanks a lot! Awesome. :) Thought about following up here today but thought you will look at it whenever you find the time. Intended to test the latest beta today and RHIM is just the most convenient way to update. I would assume that the config file is not populated correctly for the raspi5. That it is not related to the NH fission. I'm no expert but if I am not mistaken something was missing in the config when I compared it to the one that exists after the NH script installation. — Reply to this email directly, view it on GitHub <#28 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFUHCABJMMLNQ6QGNZTCP7D23J4GPAVCNFSM6AAAAAB3ACWSQCVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDQMZRGEYTGMJSHE> . You are receiving this because you commented.Message ID: ***@***.***>

[SentinelFour]

The issue is that in the pi5 the shutdown button does not work. No beeps and the system is not shut down.

I saw that the latest beta is supported, but I wanted to wait until the port forwarding and shutdown button issues have been fixed, too.
Thanks to you, port forwarding is already working. :) now I would only wait for the shutdown button.

[szafranski]

Oh, sure. :) Now I understand. Could you kindly provide the link to the config that works?

[SentinelFour]

Sure. The script provided on this page. https://nuclearquads.github.io/instructions/kitinstructions.html

 this command, which will download and run this script 
curl -s https://nuclearquads.github.io/files/nhpisetup.sh | bash -s nuclearwifi

I can also try to upload the file from the tracker tomorrow, if that helps.

On another note, just donated a little. Thanks for all your efforts!

[szafranski]

So I just perform a fresh install and button works as expected. Are you sure you used NuclearHazard version?

[SentinelFour]

I did not use the quick install but used the "standard" or manual worflow. Is it mandatory to use the quick install if I use the NH? I thought that this would be optional.

[szafranski]

Oh, understood. Will check that too

…

On Sat, Apr 26, 2025 at 10:49 SentinelFour ***@***.***> wrote: *SentinelFour* left a comment (RotorHazard/RH_Install-Manager#28) <#28 (comment)> I did not use the quick install but used the "standard" or manual worflow. Is it mandatory to use the quick install if I use the NH? I thought that this would be optional. — Reply to this email directly, view it on GitHub <#28 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFUHCAA4Z6NFKXDGYXMSCX323NCAPAVCNFSM6AAAAAB3ACWSQCVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDQMZRHE3DSNBXGM> . You are receiving this because you commented.Message ID: ***@***.***>

[szafranski]

Ok, so I perform some testing. I did a manual configuration and it works for me with one of a kits. Could you kindly provide the screen of your config file? I can assist to obtain it if needed.

[SentinelFour]

Interesting. So does this mean the shutdown button was setup properly following the standard workflow (and I did something wrong) or did you manually fix the config file afterwards?

[szafranski]

When you perform the manual configuration, default shutdown button pin in GPIO 18 since this is default for RotorHazard itself. NuclearHazard type of timers require shutdown button pin being set to GPIO 19. You can proceed with a manual configuration, you just have to be careful what you input then ;) Btw - shuttown button pin is being set under the advance part of the configuration. Let me know if that works for you and if everyting is clear now.

…

On Sun, Apr 27, 2025 at 13:40 SentinelFour ***@***.***> wrote: *SentinelFour* left a comment (RotorHazard/RH_Install-Manager#28) <#28 (comment)> Interesting. So does this mean the shutdown button was setup properly following the standard workflow (and I did something wrong) or did you manually fix the config file afterwards? — Reply to this email directly, view it on GitHub <#28 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFUHCAHH4ZS3EYFK3HVZWH323S6ZPAVCNFSM6AAAAAB3ACWSQCVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDQMZTGQYTGNJZGQ> . You are receiving this because you commented.Message ID: ***@***.***>

[SentinelFour]

I see I see. Many thanks. I think that I know what to look for now.

Just wondering. I have another NuclearHazard and that one runs on a Pi4. I (of course :-) ) also used your installer to set up that one and using the "standard" workflow, the shutdown button works fine. So is the GPIO 18 -> GPIO 19 only a special case for the Pi5 in combination with NuclearHazard hardware?

[szafranski]

To be honest I am not sure what could be the issue. Maybe this is some combination of different versions of RotorHazard severs that defaults to different configs (there were some changes introduced in last weeks). Maybe config was no properly saved at some point etc. we could dig into it, but I am not sure of that’s necessary (but interesting for sure).

…

On Sun, Apr 27, 2025 at 14:48 SentinelFour ***@***.***> wrote: *SentinelFour* left a comment (RotorHazard/RH_Install-Manager#28) <#28 (comment)> I see I see. Many thanks. I think that I know what to look for now. Just wondering. I have another NuclearHazard and that one runs on a Pi4. I (of course :-) ) also used your script to set up that one and using the "standard" workflow, the shutdown button works fine. So is the GPIO 18 -> GPIO 19 only a special case for the Pi5 in combination with NuclearHazard hardware? — Reply to this email directly, view it on GitHub <#28 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AFUHCAASBIXGSSEN4ZVEBP323TGZRAVCNFSM6AAAAAB3ACWSQCVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDQMZTGQ2DEOBVHE> . You are receiving this because you commented.Message ID: ***@***.***>